Precios incl. IVA legal más gastos de envío
Listo para envío inmediato, tiempo de entrega aprox. 1-3 días hábiles
- N.º artículo: 134036
Highlights:
- 60 Watts, selectable Mode A and Mode B
- Industrial Gigabit POE Injector with voltage booster
- accept 24 VDC to boost up voltage to 55V for 60Watts application
- 1x10/100/1000M TX PSE (802.3af/at POE+) TX
- 1x10/100/1000M TX
- Operating temp: -40°C to +75°C
Introduction
This Super Voltage Booster --- 60 Watts, high power Single port industrial POE Injector is equipped with our high efficiency ColdDesign technology which allows low input voltage, such as 24/48/56 VDC be boost up to 55VDC to provide 60Watts to 72 Watts power to your security equipment by a 4-pin selectable dip switch. The ColdDesign technology will not only boost up Input Voltage, also reduce the excessive heat problem to a minimum. It accepts the input voltage as low as 24/48 VDC to boost up to 55V to meet IEEE802.3af/at required voltage. This built-in 4 pin dip switches are able to select POE for Mode B or Mode A, to select standard IEEE802.3at 30Watts or high power 36Watts, and to select 2 pair or 4 pair for 30/36Watts or 60/72Watts power output. It is being rigorously tested for your Security, Transportation and Telco application.
Technical Details:
|
IEEE Standard |
IEEE 802.3 10Base-T Ethernet IEEE802.3af for POE IEEE802.3at for POE+ |
|
Network Connector : |
1xRJ-45 10/100/1000BaseT(X) Data 1xRJ-45 10/100/1000BaseT(X) PSE with POE Output power |
|
Network Cable |
UTP/STP Cat.5e or above Cable |
|
EIA/TIA-568 10-ohm (100m) |
|
|
Protocol |
CSMA/CD |
|
LED |
PW1(power 1) Green: ON- power good, OFF-power failed PW2(power 2) Green: ON- power good, OFF-power failed Mode A : ON- End Span PD detected Mode B: ON – Mid Span PD detected 4 Pair: ON – 60W PSE in active mode. OFF – 30W PSE in active mode. |
|
POE Pin Assignment |
Default: Mode A (End Span) V+, V+, V-, V- for pin 1, 2, 3, 6 DIP switch setting can be changed to Mode B, V+, V+, V-, V- for pin 4, 5, 7, 8 |
|
DIP Switch |
To select 2 pair (30/36Watts) or 4 pair (60/72Watts) To select Mode A, or Mode B To select standard IEEE802.3at 30watts or high power POE 36Watts |
|
Reverse polarity protection |
Present |
|
Overload current protection |
Present |
|
Power Supply |
2 Redundant power source 24V-56V VDC Power Input, |
|
Power Consumption |
1 W@24/48 VDC full load, Without POE |
|
POE power |
Maximum POE power 72watts at 24/48VDC input |
|
Removable Terminal Block |
Provide 4 pin terminal block Wire range: 0.34mm^2 to 2.5mm^2 Solid wire (AWG):12-24/14-22 Stranded wire(AWG): 12-24/14-22 Torque:5lb-In/0.5Nm/0.56Nm Wire Strip length: 7-8mm |
|
Operating Temperature |
-40° ~ 75° fully tested. |
|
Operating Humidity |
5% to 95% (Non-condensing) |
|
Storage Temperature |
-40°~85° |
|
MTBF (mean time between failure) |
510,304 hrs ( MIL-HDBK-217F) at 25°C |
|
Housing |
Rugged Metal, IP30 Protection |
|
Case Dimension (L X W X D)mm |
103.5mmx32mmx81.5mm (LxWxD) |
|
Installation mounting |
DIN Rail mounting and Wall Mounting |
|
Certifications: |
|
|
EN55022/24 |
ITE equipment |
|
EN55011 |
Industrial, Scientific and Medical (ISM) equipment |
|
Safety |
IEC EN60950-1 |
|
EMC/EMS |
CE, FCC, VCCI |
|
EMI |
FCC Part 15 Subpart B Class A, |
|
EN 50155 / EN 60068-2-6 |
Vibration |
|
EN 50155 / EN 60068-2-27 |
Shock |
|
EN 50155 / EN 60068-2-32 |
Free Fall |
| Einsatzbereich: | Industrie |
| Gehäuse: | Metall |
| PoE Leistung: | 15, 30, 60 |
| PoE Standard: | IEEE802.3af, Microsemi 60W |
| Geschwindigkeit Injektor: | 1G (1000Mbit), 10M (100Mbit), 100M (100Mbit) |